Exactly How to Install a Bath Tub Yourself: Removing and Replacing.
Exactly How to Install a Bath Tub Yourself: Removing and Replacing.
Blog Article
In this article in the next paragraph you can get a good deal of high-quality tips on the subject of How to Install a Bathtub Yourself.
Installing a bathtub isn't exactly rocket science, yet it does call for strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a new one is also a reasonably tough project. If the old tub is conveniently easily accessible, the job can move immediately; if you have to open a wall surface to eliminate the old tub and also place the new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have qualified on your own for the work and are comfortable trying it. As opposed to employing a professional to take over a halfway-completed project, it is far better to take into consideration utilizing one before you start. Opportunities are you might require an expert plumber to make tube connections.
This article will certainly assist you install a new bath tub in your shower room if you have currently purchased a brand-new bathtub and do not require to change the setup of your previous water system pipes.
Your tools and also material list ought to consist of the following:
Planning for the Setup
Firstly, the supporting frame provided with the bath should be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to stop stress on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you use all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be suited its final setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you need to do is detach the water. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of removing the existing taps can be fairly problematic because of the limited accessibility that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have been removed, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming during this process. Once the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Before carrying on to fit the new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, put the bathtub in the called for position. The wooden boards are useful in uniformly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub till the level reads level.
To install faucets, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the other faucet.
Turn on the water system as well as examine all joints as well as new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as additionally inspect the overflow outlet and the regular outlet for leakages.
Lastly, repair the bath paneling as defined in the maker's instruction manual. Tiling and also securing around the tub should wait till the tub has been used at least when as this will settle it right into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin making sure that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in position with the supplier offered backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap ports. The previous type needs to be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to crack a stiff seal, creating the water to penetrate the wall in between the bath as well as the tiling, bring about difficulties with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before securing, to permit the motion experienced when the bathtub remains in use. The sealant can break relatively very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily available on the market. It is recommended to fit the ceramic tiles making use of waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that blog entry about A Step-by-Step Guide to Installing a Bathtub when doing a search on the internet. Appreciated our piece of writing? Please share it. Let other people find it. Thanks so much for your time spent reading it.
Go Company Report this page